![]() You can do this three or four times in a row, back to back and then see if it will boot at all. If there is an issue with your RAM settings you can force a default boot by pressing and holding the power button until it cuts off on it's own. Leave it like that for about 10 minutes, then pop the battery back in first and then restore power to try it again. The red LED can be caused by defective RAM or RAM settings not right.īe sure to check your CMOS battery voltage with a voltmeter, if it's below 2.9v's replace it, if it's above 2.9v's it's probrably OK but if right at the limit (2.91V's) replace it anyway because you will before long.īe sure to attempt to clear the BIOS, by disconnecting/killing power from the wall and then remove the battery, then press the power button a few times. It's something I personally don't like it but that's how they are so, unless you've seen it act differently while it was working just know that tends to be normal. It's not unusual for the GPU fan to stay off during POST, most if not all these days are supposed to do that anyway, only starting up when they reach a given temp. That's why I was sorting what was common and not between your attempts to fix it. So, it seems the CPU itself isn't starting up inspite of a different PSU, board and CPU's in use. There was no indication of problems with the card prior to the crash.Ĭlick to expand.Lets look at what's common and what's not between the attempts you made to get it going again, specifically in terms of hardware.ĭifferent: Board and PSU in use along with the CPU. ![]() The GPU fans do not run when I try to boot, but the VGA light does not come on. I have not tried it on the new board.Īll of my case fans and the Wraith cooler have continued to run when I try to boot. I tried clearing CMOS on the old motherboard no change. I tried replacing the CMOS battery on the old motherboard no change. The machine still will not POST, and the red CPU LED continues to mock me. I also removed all the RAM and tried to boot with just one stick, swapping each one out. SSD: Samsung 860 Evo 1 TB 2.5" Solid State DriveĪttempting to narrow down the problem, I have replaced the motherboard (same model), processor (same model), and PSU (EVGA BQ 600 W 80+ Bronze Certified Semi-modular ATX). ![]() Processor: AMD FX-8350 w/stock Wraith cooler Having now spent a while, and unable to find any problems I'm all out of ideas, and I have tried scouring the Internet but nothing that has helped me as of late.Last week, my computer shut down while in "sleep" mode, and when I tried to turn it back on, I got the red CPU LED light and no POST. RGB works for the RAM, cooler, sound card but no RGB showing on GPU or MB. All fans turn on, this includes the cooler fans, my GPU fans and the fans installed individually on the case. Fans all start, then it will shut down and restart automatically but nothing changes on the display. The computer restarts itself after a minute or so when turning on. I have tried restarting and the same problem. On launch, however, the CPU indicator on the motherboard was a still red, and there was no display on my monitors. I left it for 30 minutes, thinking it was adequate enough time for the bios to update and then restarted my computer. As I did this the display did not return, and I didn't want to interrupt the bios update in the background. As it was running, I decided to switch the two DP on the back. Downloaded the bios update onto a USB and then ran it from the bios. I was having problems with a game, and while updating everything I decided to update the bios, since it wouldn't have been done since I built the computer. I built it myself and have had no problems with it until now. Long Background: I have had my computer for a couple years or so now. There is no display on either of my monitors using a display port (DP) and a HDMI cable. Waited 30 minutes until I thought the bios was updated (screen wasn't on so wanted to make sure it was installed) The CPU light on the motherboard is a still red. ![]() Short Background: Updated the bios, decided to switch the two display ports while it was updating (silly now I think of it, but I'm impatient) but the display did not return after switching them.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |